Vacuum forming machines, air (pneumatic) forming lines.
The Engineering Company MAGISTRAL produce a wide range of modern vacuum forming equipment for the manufacture of plastic wares.
Depending on the operating parameters of the equipment, vacuum-molding machine, in our company, is assigned its own unique marking, where
these parameters are reflected. Procedure for labeling is as follows:
VFM A . B . C (WGK), where
parameter A is a length of plastic sheets,
parameter B is a widht of plastic sheets,
parameter C is a depth, (height) of forming.
parameter G informs about control system vacuum molding machine, equipped a controller,
parameter W informs about bottom panel of heaters for double sided heating of plastic sheets,
parameter K informs about ceramic surface of infrared heaters for heating of plastic sheets.
The area of forming without area of clamp of plastic billet is approximately:
(А - 40 mm) х (В - 40 mm).
Depth or height of forming is (С - 50 mm).
On this page you can see some models of vacuum thermoforming equipment from EC MAGISTRAL,
as well as reflected their basic characteristics.
Vacuum forming machine type VFM 6000.1400.800 and VFM 2000.3000.1500 W.
Thermoforming machine VFM 6000.1400.800 allows to manufacture big-size plastic products length until 5.5 m.
To reduce the overall dimensions, this equipment is made by a special scheme with pulling pneumatic drive of form.
This scheme allows to protect pneumatic drive against bending loads and reduce the height of the vacuum forming machine.
Total height of vacuum molding machine is only 2500 mm.
Working stroke draped table 800 mm.
This equipment has controlling terminal with indication of the intensity of heat in the zones.
Thermoforming machine is equipped optical position sensor for the protection against the sagging heated sheet of plastic.
More details about the compact scheme vacuum molding equipment -
large vacuum-forming machine.
All vacuum forming equipment
in EC MAGISTRAL is manufactured in
accordance with the terms of reference (TOR), which must contain:
- dimensions of area forming of vacuum forming machine
- stroke of form or maximum
height (depth) of vacuum forming machine
- other important parameters of vacuum forming equipment.
TOR can contain information of product, which will be produced on this equipment.
(overall dimensions
(габаритные размеры, thickness of the plastic, type of plastic), options of complectation.
Parameters TOR are used as basis for calculation of cost of vacuum forming equipment.
Our specialization is a production vacuum forming machines with different volume of forming,
as well as automatic pneumatic or vacuum forming lines.
Before sending to buyer all thermoforming equipment is tested for forming
to obtain a qualitative sample of plastic products.
EC MAGISTRAL produces vacuum forming equipment of economy class for small-scale production of plastic products.
This thermoforming equipment has an attractive price and high quality vacuum-formed. Learn more about vacuum forming equipment of economy class.
Automatic air-pneumatic forming machines (equipment)
for the manufacture of blister package and other plastic products of films.
EC MAGISTRAL produces automatic forming equipment and
air-pneumatic machines
for the produce blister package and other plastic products of different purpose of films.
Automatic blister machine PFL-2/600
for the production blister package and package of cake,
as well as other different plastic products of films.
Automatic thermoforming line PFL-2/600
for the production blister package
and other different plastic products of films.
Our firm has a long experience of designing and manufacturing vacuum forming, thermo forming equipment .
Construction vacuum forming machines optimized for the production of the maximum possible range of plastic products, which is achieved by the presence of the following
necessary technological capabilities vacuum forming:
1. Heating of the workpiece on Vacuum Forming Machine produced by band infrared heaters with adjustable power.
The area of vacuum forming is divided into zones of heating with dimensions: 130mmh130mm (for ceramic heaters) ,
within which operator can to regulate power of IR-radiation of zonal heaters.
2. Vacuum forming machine is equipped with a mechanism of support of heated sheet in a horizontal plane of clamp.
This allows us to maintain an equal distance between the zonal
heaters and plastic workpiece, to avoid its contact with the form.
3. Vacuum forming equipment staffed by a discrete mechanism for reduction farea of forming.
4. Workpiece clamp and stroke of clamping frame of vacuum forming machine are produced by two pneumatic cilinders
with force equal 5000 n/m, which provide a reliable locking and sealing the sheet of polymer.
5. Block relay or controller produce automatic control of machine work.
Automatic control ofvacuum forming equipment produces following things:
- heating workpiece,
- stroke of form,
- on, off of vacuum valve,
- cooling of finished plastic products,
- inflate a plastic dome and separate the finished product with a form,
- lowering form.
6. Lifting of form of thermoforming machine is performed by special pneumatic cylinders with reinforced rods, with
electronic synchronization of stroke of every rod
which prevent their distruction.
it is necessary for normal work of the machine, when sum of forming forces is far of the centre of area of forming.
7. Vacuum forming machine equipped with high-performance cooling fans.
8. Vacuum forming machine equipped with special opening for front-loading of large forms.
9. Vacuum forming machine has a sealed forming box, which allows to inflate plastic sheet for
(pos.3 of scheme ВФМ)
the reducing of the difference between the thicknesses of plastic of the product.
10.Vacuum forming machine may be equipped by double-sided heaters of workpiece.
11. Heating panel with sliding mechanism is used for whole field of forming only one.
Only one total panel of heating with sliding mechanism is used for whole field of forming.
Heating panel is off in non working position.
12. In additional complectation or at using double sided heating vacuum forming machine is completed optical sensors
of control sistem of checing depth of sagging of workpiece.
In additional complectation or at using double sided heating vacuum forming machine is equipped optical sensors
of control system of sagging of workpiece.
Equipment of thermoforming
for the manufacture of plastic products.
EC MAGISTRAL manufacture vacuum thermoforming equipment for the production different kinds of plastic products.
Vacuum forming machines are constructed differently and differ non only dimensions their working parts .
Only principle of work of all vacuum forming machine is equal.
Scheme of vacuum forming machine with double sided of heating is in bottom.
Figures are denoted as follows:
Top and bottom heaters with zonal regulation of temperature of plastic
clamping frame
forming box;
lodgement of plastic sheet;
base of form (table);
heating element
drive of heater.
Principle of work
is that hot workpiece and basis of form shape vacuum chamber, where air is deleted, so plastic deforms.
description of work vacuum forming equipment is in the page
technology of vacuum thermoforming
Additionaly information of vacuum-forming (molding) machines of EC MAGISTRAL.
Mobile thermoforming complex.
Engineering Company MAGISTRAL offer mobile thermoforming complex, which is sum of some block-containers with vacuum forming machine inside.
Mobile thermoforming complex is may be complemented by other technologycal equipment (generator of electric power, extrusion equipment,
crushing equipment, drying equipment, punching press and ets).
Buying mobile thermoforming complex will help you with organization of new production, because you will not need to look
workshop for your production.
Thermoforming complex is protected from bad weather, and equipped with exhaust ventilation, lighting,
has thermal insulation and heating. To prepare for the work of the thermoforming of the complex is only necessary to set the block containers on a flat piece of land, hold them between
each other and connect them to a power source.
Additional equipment for thermoforming machines.
Vacuum-molding equipment of EG MAGISTRAL is equipped by additional
equipment allowing flexibility to provide the technology needs of the production of plastic products.
Additional equipment.
Vacuum forming equipment of EG MAGISTRAL is equipped by gate of new construction for load large forms.
This vacuum forming machines have high rate of conversion, which allows cost-effective to produce small series of plastic products.
Now, new system of control of vacuum forming equipment
installed to thermoforming equipment.
Main element of control system is a controller Mitsubishi, additional element is GOT (grafic operational terminal).
This control system give commands for drives of thermoforming equipment.
Details about system of control MITSUBISHI.
History of development of thermoforming equipment EC MAGISTRAL.
Now, vacuum forming machine VFM 3000.2000.800 W is working in the production of EC MAGISTRAL, This
equipment is for production advertizing and other plastic products.
Experience in operating this vacuum forming machine allows concluded that the two-sided heating billets increases productivity
thermoforming equipment in the 1.5 - 2 times.
Our vacuum forming machine produce toilet cabins, shower cabins, composting toilets, acrylic bath and liners.
